Function Overview: The remote maintenance function uses the Windows version of the programming software (GX Developer) to perform program transmission and monitoring functions between a modem (MODEM) and a programmable controller connected to the telephone line.
Required equipment:
1 Two Taiwan Heshan Technology F-E56CSD-V1 embedded MODEM module, comes with two serial port conversion cable 2 Mitsubishi FX2N (C) PLC + FX2N-232-BD serial port module 3 computers and a 4 internal program-controlled switch telephone line (inside)
step:
Modem selection:
In FX programmable controllers, you can use AIWA's (PV-AF288) or Omron's (ME3314B) modems. Because these two modems are too expensive and not very attractive to buy, we chose Heshan Technology F-E56CSD-V1 embedded MODEM module for debugging. In the FX programmable controller modem initial setting, you can select [user login module], [AIWA PV-AF288], [OMRON ME3314B].
Communication Specifications: Please select a modem that meets the communication specifications.
User login mode Communication: Half-duplex start-stop synchronization baud rate: 9,600 bps
Start bit: 1 data bit: 7-bit parity check: Even check stop bit: 1-bit control line: None Note: When a modem that cannot be set to the above communication standard is used, communication cannot be performed.
wiring:
1. Disconnect the programmable controller power supply;
Be sure to confirm that the programmable controller's power supply has been disconnected before starting wiring.
2, programmable controller and modem connection;
The cable connection between the modem and the RS-232C communication port of the programmable controller directly connects the MODEM's own serial port conversion cable to the RS-232C of the programming controller;
3, computer and modem connection;
The cable connection between the modem and the computer's RS-232C communication port, directly connect the MODEM's own serial port conversion cable to the computer's RS-232C;
Required equipment:
1 Two Taiwan Heshan Technology F-E56CSD-V1 embedded MODEM module, comes with two serial port conversion cable 2 Mitsubishi FX2N (C) PLC + FX2N-232-BD serial port module 3 computers and a 4 internal program-controlled switch telephone line (inside)
step:
Modem selection:
In FX programmable controllers, you can use AIWA's (PV-AF288) or Omron's (ME3314B) modems. Because these two modems are too expensive and not very attractive to buy, we chose Heshan Technology F-E56CSD-V1 embedded MODEM module for debugging. In the FX programmable controller modem initial setting, you can select [user login module], [AIWA PV-AF288], [OMRON ME3314B].
Communication Specifications: Please select a modem that meets the communication specifications.
User login mode Communication: Half-duplex start-stop synchronization baud rate: 9,600 bps
Start bit: 1 data bit: 7-bit parity check: Even check stop bit: 1-bit control line: None Note: When a modem that cannot be set to the above communication standard is used, communication cannot be performed.
wiring:
1. Disconnect the programmable controller power supply;
Be sure to confirm that the programmable controller's power supply has been disconnected before starting wiring.
2, programmable controller and modem connection;
The cable connection between the modem and the RS-232C communication port of the programmable controller directly connects the MODEM's own serial port conversion cable to the RS-232C of the programming controller;
3, computer and modem connection;
The cable connection between the modem and the computer's RS-232C communication port, directly connect the MODEM's own serial port conversion cable to the computer's RS-232C;
SCSI CABLES.Small computer system interface (SCSI) is a stand-alone processor standard for system level interface between computer and intelligent devices (hard disk, floppy drive, optical drive, printer, scanner, etc.). SCSI is an intelligent universal interface standard.
SCSI CABLES
ShenZhen Antenk Electronics Co,Ltd , https://www.antenk.com