Features:
1, digital display manual dispensing machine dialing code control the amount of glue and the interval, the digital display of glue, at a glance;
2. Hengling Automation Technology Co., Ltd. (http://) adopts 0.18CV constant flow electromagnetic control valve;
3, light switch;
4, can adjust the vacuum suction up to 15 inches / Gong Zhu (Hg);
5, exquisite metal foot switch, more durable;
6, can buy all kinds of spare parts.
Simple debugging operation:
1. Digital manual dispensing machine according to the installation diagram after the machine is connected (pay attention to the use of air pressure), the selected needle inserted in the nozzle with ≤ 3/4 liquid material and tighten;
2. Set the programming mode of 11. spit out mode, set the spout mode to F1 state, turn on the power switch and turn on the host;
3, adjustment 3. Input pressure regulator, first pull out, reversed to a large pressure, pressure is small, the pressure is placed 25PSI as the initial calibration test;
4. Press the foot switch or press the "SHOT" button until the liquid material is spit out evenly. The machine works normally.
5, through the adjustment 2. Spitting time set the dial code and replace the needle and adjust 3. Enter the pressure regulator, you can get the corresponding liquid material discharge volume;
6, adjust 5. Vacuum controller, reversed to a large vacuum pumping back, transfer to a vacuum back pumping small, so that the liquid material in the spit out when there will be no leakage;
7, need automatic timing control, by adjusting 8. Interval time setting dial code and 11. Spit mode programmer and 2. Spitting time setting dial code to achieve;
8. The amount of liquid material discharged per time is determined by the size of the input air pressure, the selection of the discharge time, the viscosity of the liquid material, and the thickness (size) of the needle tip.
Liquid drop point method:
Hengling Automation Technology Co., Ltd. Before the use of digital manual dispensing machine, calibrate the dropping amount on clean paper, place the mode switch in one of the modes (except F1), adjust the discharge time dialer and discharge time dialer, Press the foot switch or "SHOT" test key to spit out the liquid drop point. By repeating the drip correction, the corresponding liquid drop quantity will be obtained.
When dropping, the normal operation method must be followed. The barrel cannot be reversed and kept at the level of 45°. The vacuum controller cannot be adjusted too large to prevent the liquid material from flowing back into the machine.
Digital display manual dispenser dispensing and dropping (the method of injecting liquids is determined by the different liquid materials):
1, low viscosity liquid material. It can be poured directly into the syringe (cartridge). Put the needle bushing (accessory) on the barrel nozzle, hang it on the barrel holder, pour the liquid directly into the barrel from the container, or use the funnel to help.
2, medium and high viscosity liquid material. For the addition of medium to highly viscous liquids, an optional two-way feeder can be selected to simplify operations. The liquid material is first added into the storage drum, the stock drum is fixed on the shelf, the syringe is connected with the fixed adapter of the cartridge, the inlet of the cartridge is connected with a high-pressure gas source, and the air pressure is adjusted to make the liquid of the storage drum. The material is added to the syringe.
Precautions:
1. Dry pressure ≤ 100PSI high pressure air pressure should be used;
2. The loading amount of plastic injection barrel should be ≤ 3/4 containers;
3, after use should be cleaned in time glued parts;
4. When the use interval is long, the back-extraction value should be reduced;
5, the use of the opportunity to have normal exhaust exhaust sound, non-failure.
6, this note applies to Dongguan Hengling Automation Technology Co., Ltd. peristaltic 502 digital dispensing machine, rubber valve manual dispensing machine, peristaltic 502 ordinary dispensing machine, ordinary manual dispensing machine and other products.
The latest Windows has multiple versions, including Basic, Home, and Ultimate. Windows has developed from a simple GUI to a typical operating system with its own file format and drivers, and has actually become the most user-friendly operating system. Windows has added the Multiple Desktops feature. This function allows users to use multiple desktop environments under the same operating system, that is, users can switch between different desktop environments according to their needs. It can be said that on the tablet platform, the Windows operating system has a good foundation.
Windows Tablet,New Windows Tablet,Tablet Windows
Jingjiang Gisen Technology Co.,Ltd , https://www.jsgisengroup.com